electrolux washing machine loc error

Please check the door. Possible clogging inlet valve fault or closed water tap.

Samsung Washer Error Code Sud Causes How Fix Problem

The main supply is unstable.

. If its time to repair your Electrolux washing machine then its time to consult Repair Clinic for the troubleshooting help you need. The washing machine motor can be damaged when the agitator is being driven by a bad motor. The machine does not fill the water.

E01 Insufficient water supply. E04 Low temperature. The child lock has been activated making the.

If the cord is damaged the dryer may run sometimes but refuse to start at other times. If the cord is frayed or damaged it could cause the unit to short out and not run properly. How to deactivate Child Lock in my washing machine.

Two ways you can try to fix it. When the child lock is engaged it will stop you from performing any action apart from turning the appliance on or off via buttoncontrol dial. Probable door switch fault.

04 2022 Clothes Still Wet After the Spin Cycle. Malfunction Possible cause Solution The appliance does not fill with water properly. When the door lock dies on these machines it fries the electronic board so if you door lock plays up turn the power off and unplug your machine from the po.

Switch off the power to the washing machine. Remove the plug from the socket wait 30 seconds and then plug it back into the socket. Be sure to check the entire length of the cord from the point where it attaches to the dryer itself to the point.

You will not have the ability to run a cycle without opening the door. It could simply be due to the door not closing firmly. Check drain pump filter for blockages.

I turned it on like I usually do. Up to 15 cash back Having read the above issues I have 13 red flashes and 4 green flashes for the zanussi Electrolux essential 1200 6kg washerdryer can you help with this issue many thanks. Action To Take.

Or you can try to press and hold the add steam button for 5 seconds. Following this switch the appliance. Problem with communication between EEPROM and the microprocessor.

Inspect wiring for breaks. If the connections appear to be OK then remove the access panel and make sure there is no loose wiring. Ad Licensed Expert Will Answer You Now.

I had just done a wash emptied out the clothes and refilled i. Error Code Label Description Solution. If the Electrolux washing machine does not start washing and a few seconds after shutting down gives an E40 error then you need to urgently look for.

Last updated 13042022 0944. Washing Machine Repair FAQ. The washing machine does not start.

Check drain hoses for blockages and kinks. Clear code exit mode and start dryer. The machine fills then empties immediately.

Attempt to reset the appliance. Search by model. If your Electrolux dishwashing machine door locked and will not open this code will appear.

When the pump has cooled down it should work normally. Open circuit in temperature sensor. Service Information For Appliance Repair Professionals.

E03 Door unlocked. Washing machine displays padlock. A Whirlpool Washer displays a LOC error code when a Control Lock Enabled has been detected by the internal electronic diagnostics.

I am now frustrated beyond words with the poor performance of the washing machine and the I do not care attitude of the Electrolux corp. Plug the dryer into a different socket to see if the appliance functions. You wont be able to run a cycle without unlocking the door.

Ad Same-Day Shipping Easy Online Purchase No Hassle Returns. The door locked and nothing happened. The problem may be solved by switching off the power to the washing machine for about 1-2 hours and then starting a wash cycle again.

Up to 15 cash back I have a new front load washing machine. I purchased a top of the line Electrolux front load washing machine in March of 2015. Search Help by Model.

A padlock being displayed is to highlight that the Child lock function has been activated. A padlock has appeared on the display and the appliance wont function. Check the power cord running to the dryer.

I was a happy consumer for 2 weeks. Maytag Neptune Washer Stops During the Wash Cycle and Must be Manually Restarted Excessive Compressor. The normal procedure is to hold down the end of cycle signal drainspinbutton for 3 to 5 seconds.

BLTF2940ES BTF2140ES FTF2140ES FWFB9200ES GLTF2940ES LTF2140ES and LTF2940ES. However bear in mind that not all Electrolux washing machine fault codes mean a simple solution. Is your Electrolux washing machine not starting with error code E40 on screen.

E02 Door open. The appliance does not drain the water. Whether your washing machine is leaking water the door isnt latching or something else has gone wrong were here to help you identify the cause and make the repair so you can feel good.

Sometimes a simple unplugging the machine for 15minutes will reset it as well. Normal load no options. If your Electrolux dishwasher door locked and wont open this code will appear.

Vibration from motor or gearbox. If the pump has been blocked a bimetal fuse will switch off the pump. Unlocking the Control Lock on Certain Electrolux Washers and Dryers.

Questions Answered Every 9 Seconds. Plug a different product in to the same socket such as a lamp this will indicate whether the socket has an issue. Press and hold the AIR DRY button on the control panel for at least 3 seconds while the door is latched.

Treeplanter LOC is a reference to the control lock. Press and hold the AIR DRY button on the control board for a minimum of 3 seconds while the door is locked. This should unlock the door or activate the control panel for use again.

First check the connections of the motor and agitator. You Can Fix It. This must open the door or trigger the control board for usage once again.

The appliance door is open or not closed correctly.

Electrolux